- Home
- Resources
- Tech notes
- PWM and servo motor control basics
Tech notes
PWM and servo motor control basics
Duty cycle and average voltage, timer-generated PWM (frequency, resolution, center-aligned mode), choosing the frequency, RC filtering to a voltage, MOSFET and H-bridge drive with dead time, how RC servos work and pulse-width control, power and wiring, and a debugging checklist, with six diagrams and four calculators (in Korean)
The material opens in a frame kept separate from the website and does not connect to outside addresses
What this note covers
The material is in Korean. Select a chapter to jump to it in the viewer above
- 1 PWM이란
PWM(Pulse Width Modulation, 펄스 폭 변조)은 신호를 일정한 주기로 켰다 껐다 하면서 켜져 있는 시간의 비율(듀티비)을 바꾸는 방법입니다
- 2 타이머로 PWM 만들기
MCU는 하드웨어 타이머로 PWM을 만듭니다
- 3 주파수 고르기
PWM 주파수는 부하가 얼마나 빨리 반응하는지, 사람이 듣거나 보는지, 스위칭 손실 · 전자파를 얼마나 감당할지로 정합니다
- 4 PWM을 전압으로 — RC 필터
DAC가 없을 때 PWM 출력에 저항 · 커패시터(RC 저역 필터)를 달면 평균 전압을 얻을 수 있습니다
- 5 부하 구동 — MOSFET · H-브리지
MCU 핀은 수 mA ~ 수십 mA밖에 낼 수 없고 전압도 3.3 · 5 V라, 모터 · LED 줄 · 히터는 MOSFET 같은 스위치로 구동합니다
- 6 서보모터의 구조
여기서 말하는 서보모터는 로봇 · 장난감 · 소형 장치에 많이 쓰는 RC 서보(취미용 서보)입니다
- 7 서보 제어 신호
RC 서보는 펄스의 폭(High인 시간)으로 목표 위치를 받습니다
- 8 서보 전원과 배선
- 9 소프트웨어 요령
- 10 디버깅 점검표
- 11 승전 라인과 PWM · 모터
PWM 생성부터 부하 구동까지 승전이 공식 대리점으로 공급하는 라인입니다
Related notes
-
Audio ADC basics — sampling, quantization and dynamic range
How sound and speech become numbers — sample rate and aliasing, speech bandwidths, bit depth and quantization noise, sigma-delta ADCs, reading SNR, dynamic range and THD+N, gain staging from microphone to ADC, clock jitter, synchronization and echo cancellation, and a debugging checklist, with six diagrams and six calculators (in Korean)
-
MEMS microphone basics — analog and digital (PDM)
How MEMS microphones are built and work, analog versus digital (PDM) output, what the specs mean — sensitivity (dBV/dBFS), SNR, THD, AOP, dynamic range, PSRR and more — acoustic-path resonance, circuit design and a debugging checklist, with cross-section and PDM diagrams and five calculators (in Korean)
-
I2C bus basics
How the SCL/SDA open-drain bus works, speed modes, START, address, ACK and STOP, pull-up resistor sizing, clock stretching, stuck-bus recovery, level shifting and a debugging checklist — with transaction diagrams and address and pull-up calculators (in Korean)
Questions about this material?
Ask a SEUNGJUN FAE. Tell us the supplier and part number, and the team for that line will reply