The 3 modules

All modules are built around a Cortex-⁠M4 core and connect over UART. They differ in microphone count, memory and supply voltage

  • SJVR0016-NTxx-SM1 Single-mic voice recognition module

    3D rendering of the SJVR0016-NTxx-SM1, seen at an angle from above. A green board with a large square chip with leads on all four sides in the middle, a smaller square chip at the top right and small resistors and capacitors around them. Gold half-hole solder pads line the top and bottom edges, with microphone pads on the right.
    Outline 25 × 20 × 2.6 mm · 3D rendering
    MCU
    Cortex-M4 200MHz
    Microphones
    1
    Flash / RAM
    512KB / 192KB
    Supply voltage
    5V
    Interface
    UART
    Ask about this module — SJVR0016-NTxx-SM1
  • SJVR0017-DPxx-SM1 Dual-mic voice recognition module

    3D rendering of the SJVR0017-DPxx-SM1, seen at an angle from above. A blue board with two large square chips side by side — the left one with leads on all four sides, the right one with its contacts underneath. A metal-lidded crystal sits at the left edge, and gold half-hole solder pads line the top and bottom edges.
    Outline 28 × 20 × 2.6 mm · 3D rendering
    MCU
    DSP + Cortex-M4 200MHz
    Microphones
    2
    Flash / RAM
    512KB + 2MB (external) / 192KB
    Supply voltage
    1.8V
    Interface
    UART
    Ask about this module — SJVR0017-DPxx-SM1
  • SJ23Z-VR-M1 Single-mic voice recognition module · 300MHz

    3D rendering of the SJ23Z-VR-M1, seen at an angle from above. A blue board with a large square chip right of center, a smaller square chip on the left, grey metal shield clips and densely placed small parts. A gold microphone with a sound hole sits at the lower left, and gold half-hole solder pads run along all four edges.
    Outline 29 × 26 × 2.6 mm · 3D rendering
    MCU
    Cortex-M4 300MHz
    Microphones
    1
    Flash / RAM
    4MB / 830KB
    Supply voltage
    5V
    Interface
    UART
    Ask about this module — SJ23Z-VR-M1

The module images are 3D renderings made from the board design files and photos of the real modules. Part shapes are simplified

Module in 3D

SJVR0016-NTxx-SM1

Single-mic voice recognition module · 25 × 20 × 2.6 mm

3D rendering of the SJVR0016-NTxx-SM1, seen at an angle from above. A green board with a large square chip with leads on all four sides in the middle, a smaller square chip at the top right and small resistors and capacitors around them. Gold half-hole solder pads line the top and bottom edges, with microphone pads on the right.

The module images are 3D renderings made from the board design files and photos of the real modules. Part shapes are simplified

Specifications compared

Key specifications of each module. On narrow screens, swipe the table sideways

Voice recognition modules — specifications compared
Item SJVR0016-NTxx-SM1 Single-mic voice recognition module SJVR0017-DPxx-SM1 Dual-mic voice recognition module SJ23Z-VR-M1 Single-mic voice recognition module · 300MHz
MCU Note 1 Cortex-M4 200MHzDSP + Cortex-M4 200MHzCortex-M4 300MHz
Flash 512KB512KB + 2MB (external)4MB
RAM 192KB192KB830KB
Supply voltage 5V1.8V5V
Voice commands Note 2 nTrigger · nCommandsnTrigger · nCommandsnTrigger · nCommands
Interface UARTUARTUART
Size (mm) 25 × 20 × 2.628 × 20 × 2.629 × 26 × 2.6
Microphones 121
  1. The chip used in each module (maker and part number) will be added to this table once our R&D Center confirms it

  2. “nTrigger · nCommands” means the module takes multiple wake (trigger) words and commands. The number of wake words and commands, and the supported languages, are set per module and application — tell us the commands and languages you need and we will tell you what can be done Ask about commands and languages

WiFi voice module

Specifications coming soon

A SEUNGJUN voice module with WiFi. As a Wi-Fi/BLE module, its KC radio certification status will be listed. Specifications coming soon

Command customization, step by step

Wake words and commands are tailored to your product in the steps below. Timing depends on the number of commands and the scope of testing, and we confirm it when we talk

  1. 1

    Send your command list and conditions

    You send us the command list and the operating conditions — noise, distance and mounting position

  2. 2

    Module selection and tuning

    We choose the right module and tune the commands

  3. 3

    Testing in our acoustic lab

    We measure recognition and misrecognition rates

    Acoustic testing
  4. 4

    Results and samples

    We send you the test results together with samples

  5. 5

    Aging test before production

    An aging test is run before mass production starts

Built by our R&D Center, tested in our acoustic lab

R&D and chips

The equipment-operation group of our Corporate R&D Center handles voice recognition (VR) and Nuvoton audio. Nuvoton is one of the 16 lines we represent as an authorized distributor

Equipment operation Jason Son · 15 years’ experience

The chip used in each module will be added to the specification table after our R&D Center confirms it, with a link to that line’s page

Acoustic Analysis Research Center

The analysis desk at the Acoustic Analysis Research Center: two monitors running measurement software, two speakers on the left, a mixer and audio equipment in front, and a SEUNGJUN sign on the wall reading "Acoustic Analysis Lab" in Korean.
Size
4,300 × 4,400 × 2,140 mm
Noise floor
30 dBSPL

Module quality and aging tests, and misrecognition-rate measurement and debugging, are done here

Pricing and ordering

Prices by quantity are provided by quotation

  • Small quantities

    Small quantities for research or prototypes are available. Choose “Small-quantity purchase” as the purpose in the module inquiry form below

    Ask about small quantities
  • Production quotes

    Tell us your volumes and schedule and we will send you a quote

    Request a quote

Module inquiry

Choose a module and tell us the quantity and purpose. Our R&D Center will review it and contact you. Not sure yet? Choose “Recommend one for me”

Fields marked * are required

Units you need now for a small purchase; for production, your expected annual volume

Your product, the commands and languages you need, operating conditions (noise, distance, mounting) and any documents you need all help us choose the right module

More solutions