- Home
- Resources
- Tech notes
- Audio ADC basics — sampling, quantization and dynamic range
Tech notes
Audio ADC basics — sampling, quantization and dynamic range
How sound and speech become numbers — sample rate and aliasing, speech bandwidths, bit depth and quantization noise, sigma-delta ADCs, reading SNR, dynamic range and THD+N, gain staging from microphone to ADC, clock jitter, synchronization and echo cancellation, and a debugging checklist, with six diagrams and six calculators (in Korean)
The material opens in a frame kept separate from the website and does not connect to outside addresses
What this note covers
The material is in Korean. Select a chapter to jump to it in the viewer above
- 1 소리가 숫자가 되기까지
마이크가 만든 전압은 PGA(프로그래머블 게인 증폭기)로 알맞은 크기로 키운 뒤, ADC가 일정한 간격으로 값을 재고(표본화) 정해진 단계 중 가장 가까운 값으로 바꿔(양자화) 숫자(PCM)로 만듭니다
- 2 표본화와 앨리어싱
표본률 fs로 재면 fs/2(나이퀴스트 주파수)보다 낮은 소리만 제대로 담깁니다(표본화 정리)
- 3 음성 · 음향의 대역과 표본률
말소리의 뜻을 실어 나르는 성분은 대부분 수 kHz 아래에 있지만, ㅅ · ㅆ 같은 마찰음은 4 kHz 위에도 에너지가 많아 대역이 넓을수록 또렷하게 들립니다
- 4 양자화와 비트 깊이
양자화는 연속된 값을 정해진 단계 중 하나로 맞추는 일이고, 그때 생기는 차이(최대 ±½ LSB)가 양자화 잡음입니다
- 5 dBFS · 헤드룸 · 크레스트 팩터
디지털 오디오에는 넘을 수 없는 최댓값(풀 스케일)이 있습니다
- 6 오디오 ADC의 구조 — SAR과 ΣΔ
양자화 잡음의 총량이 같아도, 더 빠르게 재면 잡음이 더 넓은 주파수에 퍼져 우리가 쓰는 대역(0~fs/2) 안의 잡음이 줄어듭니다
- 7 사양 읽기 — SNR · DR · THD+N · ENOB
코덱 · ADC 데이터시트의 숫자는 이름이 비슷해도 재는 방법이 다릅니다
- 8 시스템 다이내믹 레인지와 게인 배분
아날로그 마이크를 쓰면 시스템의 위 · 아래 한계를 마이크와 ADC가 나눠 정합니다
- 9 디지털 처리에서 지킬 것
음성 처리는 표본을 묶은 프레임 단위로 합니다(예: 16 kHz에서 10 ms = 160표본, 256표본 = 16 ms)
- 10 클록 · 지터 · 동기
ADC는 클록에 맞춰 값을 잽니다. 클록 간격이 흔들리면(지터) 높은 주파수 신호일수록 값이 틀어져 잡음이 됩니다. 또 마이크 ADC와 스피커 DAC가 서로 다른 수정 발진자를 쓰면 표본률이 아주 조금 달라, 시간이 지날수록 둘이 어긋납니다
- 11 음성 처리 앞단 — 에코 제거 · 음성인식
음성 제품은 ADC 뒤에서 대개 고역 통과 필터(DC · 저역 잡음 제거) → 에코 제거(AEC) → 잡음 제거 · 빔포밍 → 자동 게인(AGC) 순서로 처리한 뒤 음성인식이나 통화로 보냅니다
- 12 측정과 디버깅 점검표
- 13 승전 라인과 오디오 ADC
음향 · 음성 입력 경로에서 승전이 공식 대리점으로 공급하는 라인입니다
Related notes
-
PWM and servo motor control basics
Duty cycle and average voltage, timer-generated PWM (frequency, resolution, center-aligned mode), choosing the frequency, RC filtering to a voltage, MOSFET and H-bridge drive with dead time, how RC servos work and pulse-width control, power and wiring, and a debugging checklist, with six diagrams and four calculators (in Korean)
-
MEMS microphone basics — analog and digital (PDM)
How MEMS microphones are built and work, analog versus digital (PDM) output, what the specs mean — sensitivity (dBV/dBFS), SNR, THD, AOP, dynamic range, PSRR and more — acoustic-path resonance, circuit design and a debugging checklist, with cross-section and PDM diagrams and five calculators (in Korean)
-
I2C bus basics
How the SCL/SDA open-drain bus works, speed modes, START, address, ACK and STOP, pull-up resistor sizing, clock stretching, stuck-bus recovery, level shifting and a debugging checklist — with transaction diagrams and address and pull-up calculators (in Korean)
Questions about this material?
Ask a SEUNGJUN FAE. Tell us the supplier and part number, and the team for that line will reply