- Home
- Resources
- Tech notes
- MEMS microphone basics — analog and digital (PDM)
Tech notes
MEMS microphone basics — analog and digital (PDM)
How MEMS microphones are built and work, analog versus digital (PDM) output, what the specs mean — sensitivity (dBV/dBFS), SNR, THD, AOP, dynamic range, PSRR and more — acoustic-path resonance, circuit design and a debugging checklist, with cross-section and PDM diagrams and five calculators (in Korean)
The material opens in a frame kept separate from the website and does not connect to outside addresses
What this note covers
The material is in Korean. Select a chapter to jump to it in the viewer above
- 1 MEMS 마이크란
스마트폰 · 무선 이어폰 · 스마트 스피커 · 음성인식 가전에 들어가는 마이크는 대부분 반도체 공정으로 만든 MEMS(Micro-Electro-Mechanical Systems) 마이크입니다
- 2 구조 — 패키지 속
MEMS 마이크 패키지는 바닥 기판 위에 MEMS 소자(소리를 받는 실리콘 구조)와 ASIC(신호를 받는 집적회로)을 나란히 올리고, 금속 덮개(캔)로 씌운 구조입니다
- 3 아날로그와 디지털
두 방식 모두 안에 든 MEMS 소자는 같은 원리입니다
- 4 디지털 출력 — PDM
PDM(Pulse Density Modulation)은 클록마다 1비트를 내는 신호로, 1이 나오는 비율(밀도)이 소리의 순간 크기를 나타냅니다
- 5 감도 (Sensitivity)
감도는 1 kHz, 94 dB SPL(= 1 Pa) 소리를 넣었을 때 나오는 출력입니다
- 6 SNR과 자체 잡음
SNR(Signal-to-Noise Ratio)은 94 dB SPL, 1 kHz 소리를 넣었을 때의 출력과 소리가 없을 때 마이크가 스스로 내는 잡음 출력의 차이입니다
- 7 THD · AOP · 다이내믹 레인지
THD(Total Harmonic Distortion, 전고조파 왜율)는 출력에 섞인 고조파(2배 · 3배 … 주파수) 성분의 비율입니다
- 8 그 밖의 사양 읽기
- 9 음향 설계 — 소리가 들어오는 길
데이터시트의 주파수 응답은 마이크 하나만 잰 값입니다
- 10 회로 설계
ADC 쪽 사양(SNR · 다이내믹 레인지)을 읽는 법과 마이크부터 ADC까지의 게인 배분은 오디오 ADC 기술 노트에서 더 자세히 다룹니다
- 11 고르는 요령과 디버깅 점검표
- 12 승전 라인과 마이크
마이크와 그 신호를 받는 칩에서 승전이 공식 대리점으로 공급하는 라인입니다
Related notes
-
PWM and servo motor control basics
Duty cycle and average voltage, timer-generated PWM (frequency, resolution, center-aligned mode), choosing the frequency, RC filtering to a voltage, MOSFET and H-bridge drive with dead time, how RC servos work and pulse-width control, power and wiring, and a debugging checklist, with six diagrams and four calculators (in Korean)
-
Audio ADC basics — sampling, quantization and dynamic range
How sound and speech become numbers — sample rate and aliasing, speech bandwidths, bit depth and quantization noise, sigma-delta ADCs, reading SNR, dynamic range and THD+N, gain staging from microphone to ADC, clock jitter, synchronization and echo cancellation, and a debugging checklist, with six diagrams and six calculators (in Korean)
-
I2C bus basics
How the SCL/SDA open-drain bus works, speed modes, START, address, ACK and STOP, pull-up resistor sizing, clock stretching, stuck-bus recovery, level shifting and a debugging checklist — with transaction diagrams and address and pull-up calculators (in Korean)
Questions about this material?
Ask a SEUNGJUN FAE. Tell us the supplier and part number, and the team for that line will reply