- Home
- Resources
- Tech notes
- I2C bus basics
Tech notes
I2C bus basics
How the SCL/SDA open-drain bus works, speed modes, START, address, ACK and STOP, pull-up resistor sizing, clock stretching, stuck-bus recovery, level shifting and a debugging checklist — with transaction diagrams and address and pull-up calculators (in Korean)
The material opens in a frame kept separate from the website and does not connect to outside addresses
What this note covers
The material is in Korean. Select a chapter to jump to it in the viewer above
- 1 I2C란
I2C(Inter-Integrated Circuit)는 SCL(클록)과 SDA(데이터) 두 가닥으로 보드 위의 여러 칩을 잇는 직렬 버스입니다
- 2 신호와 전기적 특성
오픈 드레인 출력은 선을 Low로 당기거나 놓을 수만 있습니다
- 3 주소와 한 번의 전송
전송은 START(S)로 시작해 STOP(P)으로 끝납니다
- 4 풀업 저항 계산
풀업 저항에는 두 한계가 있습니다. 너무 작으면 Low로 당길 때 전류가 커서 출력이 VOL 아래로 내려가지 못하고, 너무 크면 RC로 늦게 올라가 상승 시간 규격을 넘습니다
- 5 클록 늘이기와 중재
타깃이 데이터를 준비할 시간이 필요하면 SCL을 Low로 잡고 있습니다
- 6 버스 멈춤 복구
가장 흔한 고장은 SDA가 Low에 묶여 START를 낼 수 없는 상태입니다
- 7 전압이 다른 장치 · 버스 늘리기
1.8 V 센서와 3.3 V MCU처럼 VDD가 다르면 양방향 레벨 변환이 필요합니다
- 8 SMBus · I3C와의 관계
SMBus 장치는 대개 I2C 컨트롤러로 다룰 수 있지만, 시간 제한과 입력 문턱 전압이 다를 수 있으니 데이터시트를 함께 봅니다
- 9 디버깅 점검표
- 10 승전 라인과 I2C
I2C를 쓰는 설계에서 승전이 공식 대리점으로 공급하는 라인입니다
Related notes
-
PWM and servo motor control basics
Duty cycle and average voltage, timer-generated PWM (frequency, resolution, center-aligned mode), choosing the frequency, RC filtering to a voltage, MOSFET and H-bridge drive with dead time, how RC servos work and pulse-width control, power and wiring, and a debugging checklist, with six diagrams and four calculators (in Korean)
-
Audio ADC basics — sampling, quantization and dynamic range
How sound and speech become numbers — sample rate and aliasing, speech bandwidths, bit depth and quantization noise, sigma-delta ADCs, reading SNR, dynamic range and THD+N, gain staging from microphone to ADC, clock jitter, synchronization and echo cancellation, and a debugging checklist, with six diagrams and six calculators (in Korean)
-
MEMS microphone basics — analog and digital (PDM)
How MEMS microphones are built and work, analog versus digital (PDM) output, what the specs mean — sensitivity (dBV/dBFS), SNR, THD, AOP, dynamic range, PSRR and more — acoustic-path resonance, circuit design and a debugging checklist, with cross-section and PDM diagrams and five calculators (in Korean)
Questions about this material?
Ask a SEUNGJUN FAE. Tell us the supplier and part number, and the team for that line will reply